Shanghai 1 5/8" Radial Arm Drill model Z5040B



Search our site Loading				Questions ? Call us at 905-624-5536

Shanghai Z-5040-B 1 5/8" radial arm drill press

Shanghai Z5040B Radial Arm Drill with Power Feeds and Semi-automatic Tapping Cycle

Drilling capacity	1 5/8"	40 mm
Tapping capacity	1 "	M27
Diameter of column	8.66"	220 mm
Spindle travel	7.9"	200 mm
Spindle axis to column	25.2"	640 mm
Max. spindle nose to table	26.6"	675 mm
Spindle taper	MT4
Spindle speed range	48 ～ 2,400 RPM
Number of spindle speeds	18
Spindle motor with geared head	2.9 Hp
Optional variable speed head	40 - 2,000 RPM
Spindle motor with variable speed	4 Hp
Spindle feeds	4
Feed rates	3, 6, 11 and 14 thou / rev	0.08, 0.15, 0.27, 0.35 mm / rev
Worktable surface	41.3" x 15.9 "	1050× 405 mm
Rear floor plate surface	47.24" x 21.65"	1,200 × 550 mm
Box table for floor plate	~24 x 16 x12"	600 x 420 x 300 mm
Tilting table surface	~24" x 16"	600 x 398mm
Worktable and base T-slots	2-14mm and 2-18mm
Coolant motor ( optional )	1.6 US GPM	6 L / min
Net Weight	5,588 Lb.	2540 Kg.
Packing dimennsions	37" x 22.44" x 88.6"	225 × 130 × 225 cm

Geared head Radial arm drill press Shanghai model Z5040B

For perspective this shows a similar machine with an operator.
The tilting table is shown mounted on the left side of the base.

Showing the rear alternate work position with tilting table and floor plate Z5040B

There are two alternate work stations: One side of the base and one on the rear of the base. Both are machined and T-slotted to allow direct mounting of a workpiece, or mounting of the tilting table or box table.. This is all standard equipment.

the electrical panel of the Z5040B showing CSA/CE/UL approved components

The main electrical components are CSA,
CE and UL approved.
Control circuits are low voltage.

showing the side and rear T-slotted work mount postions of the Z5040B

Rear view of the Z-5040-B showing the 2 and 3 areas of T-slots provided for mounting workpeices, jigs, fixtures or direct mounting of workpieces.

The floor plate, box table and tilting table are all standard equipment.
The coolant tank has been put up on the base and the rubber chip protector has lifted to reveal the T-slots on the left side of the base.

	The head can be rotated 180 degrees to position over the back of the machine. Machined and T-slotted faces on the back and one side of the base can be used to mount workpieices directly, or a tilting table can be mounted. Furthermore a separate floor plate and box table can be mounted. The floor plate, box table and tilting table are all standard equipment. Pushbutton hydraulic clamping. Digital readout of drilling depth Geared headstock with hardened and ground steel gears Four power feeds actuated by pushbuttons in each feed lever, engaged by electromagnetic clutch. with release built into the depth gauge Semi-automatic tapping cycle. Spindle runs forward to tap and reverses when the pushbutton in the feed lever is pushed, then reverses again at the top of the stroke, ready for the next hole. Worktable can be rotated ±180°and tilted ±45° Both motor-driven and manually operated lifting system of worktable. Coolant system Adjustable depth stop with inch and metric scales Table has double acting linked clamps with safety interlock to power elevation Drill speed chart for iron and steel on faceplate Drill chuck guard with built in switch to CE standards Available with 600/3/60 electrics, CSA approved, and 230/3/60 Standard equipment includes a 1/2" keyed drill chuck with arbour, a MT4-3, MT4-2 and MT2-1 sleeves, drifts, anchor bolts and manual. Built in worklight CE, CSA, UL approved main electrical components Digital display of spindle speed and drilling depth Ideal choice for single piece, small batch and mass production for drilling, counter boring, reaming, tapping, spot facing etc.
A version of this machine is available with a 4 Hp inverter drive giving variable speeds. Speeds are displayed digitally on the head.

Click images for larger views

Shanghai Z5040B radial arm drill with the head rotated 180 degrees to the rear work position with a floor plate and T-slots on the machine base

Showing the head rotated 180 degrees to access the read work position. In this case the floor plate is accessible for large workpieces. The side and rear face of the base are T-slotted for mounting fixtures or the tilting table.

This photo shows the tilting table on the rear T-slotts and the floor plate to the side with the box table on it. The floor plate, box table and tilting table are all standard equipment.