Search our site
Loading
HH Roberts Machinery Ltd logo
Questions ?
Call us at 905-624-5536
H.H. Roberts Machinery Limited
1324 Matheson Blvd E., Mississauga, Ontario, Canada. L4W-2Z7, Fax 905-624-9065
asdf   asdf

HH Roberts AnnnYang DY460 and 510:
18" and 20" Swing
Available in 34", 50", 60" and 80" centres
and spindle bores of 3 1/8" or 4 1/8"

Available with
  Fagor CNC logo
Fanuc

18" x 50" In stock with Hydraulic chuck
The 18" x 50" model shown with a Pragati electric turret. Annnyang 18" CNC lathe
Download the Annnyang CNC lathe Catalog

Annn Yang 18" CNC lathe with Anilam 4200 control Pragati Electric Turret
Here we show the 18: x 50" model with sliding doors and and economical 4 way electric turret. Here is a close up of the turret disc showing the 8 turning positions as well as 3 bolt on boring tool block and one facing tool block. Note the abundance of coolant ports.

Headstock of HH Roberts CNC lathe The headstock is clean and straightforward. Three gear ranges provide good power from top to bottom. Our USA made vector drive gives us much wider range of speed in each gear than is indicated on the headstock nameplate.

Base of Annnyang 18" CNC lathe The base on all of this series machines is a solid, one piece casting.

work area if the annnyang cnc lathe To the left is the optional automatic 4 way indexing turret toolpost.  This toolpost has 2 coolant ports ( not visible ) on the base below the turret.  They coolant ports are normally fitted with a copper tube to allow adjustment of the aim.  They coolant ports are fixed and do not change with the tooling.  This is a very economical automatic toolpost if you can live with only 4 tools and the coolant function.  The picture was taken during fitting and the rear chip panel has be removed as well as the rear cross slide cover.  This toolpost must be mounted on the rear of the cross slide. The photo was take during fitting and the rear splash cover and rear cross slide cover have been removed.
These turrets do not lift up during unclamp or rotation.

 
DY-410
DY-460
DY-510
swing over bed
410mm
16"
460mm
18"
510mm
20"
swing over cross slide
210mm
8"
270mm
10-1/2"
310mm
12.2"
distance between  centers
750 / 1000 / 1500mm
30" / 40" /  60"
850 / 1250 / 1500 / 2000mm
33" / 50" / 60" / 80"
max. cutting diameter
300mm
12"
335mm
13"
max. cutting length
500 / 750 / 1150mm
29.5" / 45"
500 / 900 / 1150 / 1650mm
20" / 35.5" / 45" / 65"
spindle nose
D1-6"
D1-8"
spindle bore
54mm
2 1/8"
standard 80mm   3-1/8"
optional  102mm  4"
bar capacity
52mm
2"
standard 78mm     3"
optional 100mm     4"
spindle taper
MT 6
MT8  /  MT10
spindle speed
H 600-3000
H 140-2000
M 200-1300
M 50-850
L 50-450
L 30-300
cross travel ( X  axis)
180mm   7"
200mm   8"
Iongitudinal travel ( Z  axis)
500 / 750 / 1250mm
29.5" / 45"
550 / 950 / 1200 / 1700mm
20" / 35.5" / 45" / 65"
rapid traverse X
5M/min
200 ipm
rapid traverse Z
10M/min
400 ipm
feed rate
0.001-500mm/rev      0.0004 - 20" / rev
spindle power
10 HP
12 1/2 HP
optional 15 Hp
axis servo motors
2.1NM - 4.5NM
optional hydraulic pump
2HP /  1.5KW
bed width
305mm
12"
330mm
13"
tailstock quill diameter
54mm   2"
75    3"
tailstock quill travel
150   5"
tailstock quill taper
MT 4
MT 5
net weight (approx.)
1800 / 2000 / 2200 KGS
2150 / 2400 /
2650 / 3200  KGS
2200 / 2500 /
2700 / 3250  KGS
We can offer a selection of hydraulic steady rests for CNC lathes from Rohm and Kitagawa
Roehm / Rohm automatic self centering steady rest
showing an open steady rest